Double Glazing Door Lock Repairs
Are your uPVC door or window mechanism not working properly? Perhaps the door or window handles aren't aligned properly or are difficult to use.
You'll lose energy in the event that your double-glazed doors fail to perform as they should. This can also increase the likelihood of burglaries. Owen the Locksmith can repair your door lock for reasonable costs.
Snapped Key
It can be a hassle when a key is snapped inside the lock. It also poses an issue for security, since the door might not lock and could leave you vulnerable to burglars. There are a few quick solutions you can use to resolve the issue and make your door functional again.
Keep calm. If you panic and start playing around with your keys, you might just end up pushing the broken piece of the key deeper into the lock, making the situation much worse.
Spray WD-40 or another penetrating oil, into the lock. This will assist the broken piece to be removed more easily. You can also make use of a screwdriver to break up any stuck pieces that could be hindering the flow. If you have a chunk of the key that is stuck, grab it with a paperclip or another thin metal object and pull it. Both methods work, but be careful not to push the damaged piece of the key further into the keyway.
Some paperclips have grooved edges that could be used as a hook extractor and jigsaw blades are also suitable for this purpose. If you don't have any of these then you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers can be used to grip and pull out the last part of the broken key.
If you are unable to remove the broken piece of key Use a lock deicer. It's usually available at most hardware stores, and it is used to freeze any water or ice that could be inside the lock.
If none of these tricks are working then it's probably the time to contact a locksmith. Fitlocks specialists are able to quickly fix problems with uPVC door locks and mechanisms that have snapped keys as well as broken handles. They can also modify your double glazing door mechanisms to make them more user-friendly. Request a repair for your double glazing through us online or give us a phone call to discuss your requirements.
Broken Cylinder
A damaged cylinder poses an immediate security risk. It's fortunately a simple repair for an expert locksmith to complete. A locksmith must tap the cylinder to fix it. They can do this with an hammer or another tool, but the most efficient method is to employ an extended match or piece of wire. The match or wire's end close to the keyway. After this, the locksmith will hit the lock to break it open. This is more secure than using the hammer, which could cause damage to the lock.
The most common cause of cylinder head cracks is overheating. This can happen when the block and cylinder head are made of different metals like cast-iron and aluminium. When various metals heat up and cool down at different rates, it could create hotspots locally that expand faster than the rest of the head of the cylinder, leading to cracks.
Another possible cause of cracks in cylinders is corrosion. If the head and block of a cylinder are not maintained in a timely manner they may be corroded or rust and cause them to expand faster than they would normally. This can cause cracks over time.
If your uPVC window or door lock is rigid and requires a lot more pressure to turn it could be due to a variety of causes. This problem can be caused by a faulty locking mechanism or misalignment as well as a worn-out handle.
This is a straightforward and inexpensive fix that most double glazing owners can do. A professional locksmith is able to solve the issue within one hour of arriving at your home. Depending on your needs they can change the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith will be able to advise you on the most cost-effective solutions for your home. They can even suggest upgrades to high-security 3 Star euro cylinders TS007 that provide an extra layer of protection against burglars. It's a small amount to enjoy the peace of mind that comes from knowing your uPVC door is secure.
Broken Handle
Window handle locks have intricate mechanisms that wear out with age and use, so it's not a surprise that they can break. If yours fails it's difficult to pinpoint the cause of the issue and make sure you fix it correctly.
The issue could be with the internal locking mechanism or the latch, fixing the broken handle will increase your uPVC double glazing door's security and help you to stop drafts. If you do not repair or replace your handle can be very costly and may harm the door's frame as well as lock and frame, so it's worth spending some time to do it right.
Screwdriver Open the window remove the screw that holds the handle. The screw should be on the inside face of the back plate, which is usually concealed by an aesthetically pleasing cover for the screw reasons. It is not recommended to be able to replace any internal parts of the handle such as the levers and plates on either side. Keep them in the same arrangement so that it is easier to replace them if needed.
Then, using a second screwdriver loosen the screw that connects the handle with the spindle in the back. Once the screw is loose, you should be in a position to pull the handle off and pull off the damaged spindle. Replace this with a new one, ensuring it's the same size as the previous one (you can usually find these on the internet or at hardware stores) and then securely screw it in the right place. Do not overtighten the screw as this could harm the handle as well as the window frame.
Check that the new handle is installed after which you can close and test the handle. The hope is that it will function smoothly and you'll be able unlock your window.
Make sure to check that your uPVC window is shut properly when you're using the handle. If they're not closing correctly, you could encounter draughts or damp in your home. It could also affect the energy efficiency of your home. A local window company, such as Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they shut correctly.
Broken Spindle
It is quite common that the spindle within the handle breaks, rather than the handle itself. This is especially frequent in uPVC tilt and turn windows. These windows require a handle to operate an electronic locking mechanism within the window frame. The handle is connected to a central rod that activates a series of cams with a mushroom shape that secure the window frame keep. If the dead latch mechanism does not open when the handle is turned it is likely that the spindle has been damaged, this can be an extremely frustrating issue.
There are ways to fix this issue. A reputable locksmith will be able to quickly and efficiently repair this issue. They can disassemble the window handle by using a tool that removes the wheel component of the mechanism that is where the spindle is. This is done without damage to the handle or window frame.
Once the wheel has been removed, the technician will inspect the spindle and determine what caused it to break. double glazing Slough involves disassembling the spindle and inspecting each component, noting any damage or excessive wear. This process is usually performed by technicians in an environment that is clean.
Next, clean the damaged spindle. This will help get rid of any dirt or other debris that might be preventing it from working normally. The spindle can be replaced or repaired. If it's being replaced, the technician could use a dowel of a similar size to the one used in the first and drill mating holes into both pieces of the spindle. This will ensure that the new spindle has an exact fit with the handle.
If the damaged spindle is beyond repair, it may be required to replace it completely. Home centres sell generic substitutes, but if your window design is unique you'll need to contact an expert in woodworking or cabinet making who can replicate the exact part. After the spindle is installed, it is fixed to the handle. Line up the screw holes on the handle to the existing screws in the frame. Once the new handle is firmly in place, you'll be able to operate your uPVC window.